This is often done using the reset button on the back of your router. Rangers apprentice 12 epub download. You may have to use a paperclip to push a recessed button on the back of the router. Unplug the router, push and hold the reset button while you plug the power cord back in. Continue holding the reset button for up to 30 seconds and let the router boot as normal.

This was a tad difficult to find as I searched for “Convert Fritz!Box to Switch” instead of “Convert Fritz!Box to Access Point”. Since I had an old lying around (from ) and wanted to extend the cabled LAN for my brothers Fritz!Box 7490 with some low-bandwidth devices (max 100 megabit/second) I searched for Switch. Oh I had to factory reset it as well as I forgot the management credentials. The AVM help on this is cumbersome: but the xs4all help includes a web-reset procedure as part of which translates to: • Switch off the Fritz!Box (as this procedure needs to be done within 10 minutes of switching it on) • Connect LAN2 to your computer • Switch on the Fritz!Box • Wait for a DHCP IP or (if you know the IP addresses) configure IP manually • Go to the web-interface URL • Indicate you forgot your password.

Restore Factory Settings Anyway: with the above steps it becomes a Managed Switch (and if you don’t disable WiFi: Access Point too) that uses the primary internet connection as DHCP server (so it gets an IP address itself as well which means you can manage it). This is what happens: When the FRITZ!Box is used as an IP client, it shares the existing Internet connection of your other router. In this case the firewall of the FRITZ!Box is disabled. Network devices connected to the FRITZ!Box still obtain their IP settings from the other router. All network devices have unrestricted access to all other network devices, regardless of whether they are connected to the FRITZ!Box or the other router. These are the steps: 2 Configuring the FRITZ!Box. • Click “Internet” in the.

• Click “Account Information” in the “Internet” menu. • Select “Other Internet service provider” from the drop-down list “Internet service provider”. With some regional settings, this entry will not be displayed until you select “More Internet service providers”. • Enable the option “External modem or router” in the “Connect via” or “Connection” section.

• Select “Share existing Internet connection in the network (IP client mode)” in the “Operating Mode” section. • Enter the relevant speeds of your Internet connection in the “Downstream” and “Upstream” fields. Example: Enter 32000 for a downstream of 32 Mbit/s; enter 2000 for an upstream of 2 Mbit/s. • Click on “Change connection settings”. • Configure the IP settings: • If the router in the network provides a DHCP server: • Enable the option “Obtain the IP address automatically (DHCP)”.

• If the router in the network does not provide a DHCP server: • Enable the option “Configure the IP address manually”. • Enter IP settings that fit with the IP network of the router: • “IP address”: IP address from the router’s network. Example: The router has the IP address 192.168.100.1 (subnet mask 255.255.255.0) and is therefore in the network 192.168.100.0.

In this case you can enter 192.168.100.2 as the IP address. Important:The IP address you select may not already be used by another device in the router’s network. • “Subnet mask”: Subnet mask of the router • “Default gateway”: IP address of the router • “Primary DNS server”: IP address of the router • Click “Apply” to save your settings.

Telnet is a protocol that enables a remote connection to a system using the console. Don’t mix this up with a remote desktop. The proticol is not secure! In this example we will establish a connection to a Linux system running on our Fritz!Box.

Since telnet is an unsecure connection, I explain how to establish a secure connection in section. There is no need to worry about security since we open telnet only internally – a potential hacker would only come from the internal net. CAUTION: Other having access internally, as family or or flat sharers would have acces and coul get acces privileges (eg. If this could happen I recommend to switch off telnet access after SSH is installed. Until that is done you have to accept the risk! Set up or turn off telnet Dial with phone switched doff: - #96*7* Telnet on - #96*8* Telnet off Hint: If successfull you get a confirmation beep for 1 sec.